•  
  •  

Telephone line based audio muting and light on circuit

Very often when enjoying music or watching TV at high audio level, we may not be able to hear a telephone ring and thus miss an important incoming phone call. To overcome this situation, the circuit presented here can be used. The circuit would automatically light a bulb on arrival of a telephone ring and simultaneously mute the music system/TV audio for the duration the telephone handset is off-hook. Lighting of the bulb would not only indicate an incoming call but also help in locating the telephone during darkness.
On arrival of a ring, or when the handset is off-hook, the inbuilt transistor of IC1 (opto-coupler) conducts and capacitor C1 gets charged and, in turn, transistor T1 gets forward biased. As a result, transistor T1 conducts, causing energisation of relays RL1, RL2, and RL3. Diode D1 connected in anti-parallel to inbuilt diode of IC1, in shunt with resistor R1, provides an easy path for AC current and helps in limiting the voltage across inbuilt diode to a safe value during the ringing. (The RMS value of ring voltage lies between 70 and 90 volts RMS.) Capacitor C1 maintains necessary voltage for continuously forward biasing transistor T1 so that the relays are not energised during the negative half cycles and off-period of ring signal. Once the handset is picked up, the relays will still remain energised because of low-impedance DC path available (via cradle switch and handset) for the in-built diode of IC1. After completion of call when handset is placed back on its cradle, the low-impedance path through handset is no more available and thus relays RL1 through RL3 are deactivated.
As shown in the figure, the energised relay RL1 switches on the light, while energisation of relay RL2 causes the path of TV speaker lead to be opened. (For dual-speaker TV, replace relay RL2 with a DPDT relay of 6V, 200 ohm.) Similarly, energisation of DPDT relay RL3 opens the leads going to the speakers and thus mutes both audio speakers. Use ?NC? contacts of relay RL3 in series with speakers of music system and ?NC? contacts of RL2 in series with TV speaker. Use ?NO? contact of relay RL1 in series with a bulb to get the visual indication

If there are any problems please contact webmaster@electronic-circuits-diagrams.com

Please share & like


New Johnson Controls EasyIO-FW-08  picture

New Johnson Controls EasyIO-FW-08

$300.00



JOHNSON CONTROLS LP-FXNDIO-16-0 / LPFXNDIO160 16 Channel I/O Module picture

JOHNSON CONTROLS LP-FXNDIO-16-0 / LPFXNDIO160 16 Channel I/O Module

$200.00



Johnson Controls MSNCE25660 Metasys Network Control Engine picture

Johnson Controls MSNCE25660 Metasys Network Control Engine

$600.00



Johnson Controls Metasys AS-UNT121-1 Controller Unit picture

Johnson Controls Metasys AS-UNT121-1 Controller Unit

$79.99



Johnson Controls VMA1630 Metasys VAV Controller picture

Johnson Controls VMA1630 Metasys VAV Controller

$650.00



Johnson Controls F93B-1C Air Volume Control for Deep Wells picture

Johnson Controls F93B-1C Air Volume Control for Deep Wells

$39.61



Johnson controls temperature control A19ABA-40C picture

Johnson controls temperature control A19ABA-40C

$70.00



JOHNSON CONTROLS FXNDIO16 MODULE - Tridium Niagara Honeywell Vykon AX NDIO 16 picture

JOHNSON CONTROLS FXNDIO16 MODULE - Tridium Niagara Honeywell Vykon AX NDIO 16

$49.99



JOHNSON CONTROLS PAN-ENC1620WDP / PANENC1620WDP (BRAND NEW) Sealed BOX Code 128 picture

JOHNSON CONTROLS PAN-ENC1620WDP / PANENC1620WDP (BRAND NEW) Sealed BOX Code 128

$150.00



JOHNSON CONTROLS G600HL-1 Ignition Control Module picture

JOHNSON CONTROLS G600HL-1 Ignition Control Module

$168.00