•  
  •  

Remote control using VHF modules

A few designs for remote control switches, using VG40T and VG40R remote control pair, are shown here.
The miniature transmitter module shown in Fig. 1, which just measures 34 mm x 29 mm x 10 mm, can be used to operate all remote control receiver-cum-switch combinations described in this project. A compact 9-volt PP3 battery can be used with the transmitter. It can transmit signals up to 15 metres without any aerial. The operating frequency of the transmitter is 300 MHz. The following circuits, using VG40R remote control receiver module measuring 45 mm x 21 mm x 13 mm, can be used to:
(a) activate a relay momentarily,
(b) activate a relay for a preset period,
(c) switch on and switch off a load.
To activate a relay momentarily (see Fig. 2), the switch on the transmitter unit is pressed, and so a positive voltage is obtained at output pin of VG40R module. This voltage is given to bias the relay driver transistor. The relay gets activated by just pressing push-to-on micro switch on the transmitter unit. The relay remains energised as long as the switch remains pressed. When the switch is released, the relay gets deactivated. Any electrical/electronic load can be connected via N/O contacts of the relay.
To activate a relay for a preset period (refer Fig. 3), the switch on the transmitter unit is pressed momentarily. The transistor gets base bias from VG40R module. As a result the transistor conducts and applies a trigger pulse to IC 555, which is wired as a monostable multivibrator. The relay remains activated till the preset time is over. Time delay can be varied from a few seconds to a few minutes by adjusting timing components.
To switch on and switch off a load (refer Fig. 4), a 555 IC and a decade counter 4017 IC are used. Here the 4017 IC is wired as a flip-flop for toggle action. This is achieved by connecting Q2 output to reset terminal while Q1 output is unused. Q0 output is used for energising the relay. The relay is activated and deactivated by pressing the transmitter switch alternately. So, to activate the load, just press the transmitter switch once, momentarily. The relay will remain activated. To switch off the relay, press the transmitter switch again. This process can be repeated. Time delay of monostable multivibrator is set for about one second.
Note: Short length of shielded wire should be used between VG40R receiver module output and the rest of the circuit. The transmitter with 9V battery must be housed inside a nonmetallic (say, plastic) cabinet for maximum range of operation.

If there are any problems please contact webmaster@electronic-circuits-diagrams.com

Please share & like


USB TL866II Plus Programmer EPROM EEPROM Flash MiniPro BIOS AVR AL PIC SP MCU picture

USB TL866II Plus Programmer EPROM EEPROM Flash MiniPro BIOS AVR AL PIC SP MCU

$58.50



CH341A 24 25 Series EEPROM Flash BIOS USB Programmer Module + SOIC8 Test Clip US picture

CH341A 24 25 Series EEPROM Flash BIOS USB Programmer Module + SOIC8 Test Clip US

$13.75



1PCS EEPROM IC ATMEL DIP-28 AT28C64B-15PC  picture

1PCS EEPROM IC ATMEL DIP-28 AT28C64B-15PC

$1.40



US Stock 5pcs W27C512-45Z W27C512 DIP IC EEPROM 512KBIT 45NS picture

US Stock 5pcs W27C512-45Z W27C512 DIP IC EEPROM 512KBIT 45NS

$15.98



CH341A 24 25 Series EEPROM Flash BIOS USB Programmer + SOIC8 Clip picture

CH341A 24 25 Series EEPROM Flash BIOS USB Programmer + SOIC8 Clip

$21.39



PROM EPROM EEPROM EEROM UVPROM Modules picture

PROM EPROM EEPROM EEROM UVPROM Modules

$4.50



EEPROM BIOS USB Programmer CH341A + SOP8 Clip + 1.8V Adapter + SOP8 Adapter picture

EEPROM BIOS USB Programmer CH341A + SOP8 Clip + 1.8V Adapter + SOP8 Adapter

$14.22



HighSpeed Programmer MiniPro USB TL866II Plus EPROM EEPROM FLASH BIOS AVR AL PIC picture

HighSpeed Programmer MiniPro USB TL866II Plus EPROM EEPROM FLASH BIOS AVR AL PIC

$58.50



AT28C256-15PU EEPROM IC ATMEL DIP-28 AT28C256-15PU IC picture

AT28C256-15PU EEPROM IC ATMEL DIP-28 AT28C256-15PU IC

$2.99



HighSpeed Programmer MiniPro USB TL866II Plus EPROM EEPROM FLASH BIOS AVR AL PIC picture

HighSpeed Programmer MiniPro USB TL866II Plus EPROM EEPROM FLASH BIOS AVR AL PIC

$58.60