IndusTec 20A 125V DPDT 6 screws (On)/Off/(On) Toggle Switch Momentary 3 Pos 12V for Sale

Recent Threads

On eBay Now...

IndusTec 20A 125V DPDT 6 screws (On)/Off/(On) Toggle Switch Momentary 3 Pos 12V For Sale

When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

IndusTec 20A 125V DPDT 6 screws (On)/Off/(On) Toggle Switch Momentary 3 Pos 12V:
$8.29

Visit store

E-TEN223 or KN3C-223
2P2T DP2T 2PDT
Maintained and Momentary explained
A Maintained switch is noted several ways in different industries On Off On or Latched or Latching or Locking
It is going to Latch Lock in position you or someone else places it. Used for non jogging operations like pumps fans or lights
A momentary switch denoted in several ways also is (On) Off (On) or Resetting or automatic reset or springing
This term means it will return spring reset automatically to a position (usually off) when you release it. For jogging operations like lift hoist winch or door

TOG2236RS

Video will open in a new window
Using the App? Paste link into a browser window:

[isdntekvideo]
WATERPROOF IT HERE
Waterproof boots for switches

Sold and shipped from USA!

This listing is for one (1) Double Pole Double Throw 3 Position Toggle Switch
These switches are momentary (they spring to off center position automatically when released)
These Switches are very high quality with a super LIGHTWEIGHT construction.
All Switches are brand new and purchased directly from the manufacturer
These can be used as Motor Polarity Reversing Switch with our kit

Features:

Quantity: 1 Toggle Switch
Switch Type: DPDT
Switching Function: Momentary
Power Rating: 15 Amps @ 250 VAC
20 Amps @ 125 VAC
Body Length: 1.26" or 32mm
Body Width: 0.79" or 20 mm
Body Height: 1 1/8"" or 29 mm
Overall Height: 2.24" or 57mm

Uses

Car Truck Boat ATV UTV Airplane

Autos Marine Industrial Robotics Automation Aviation

12-24 DC Motors Manufacturing

Mower Deck Lift Switch 078-807-00

Cole Hersee 55054

To clear up voltage ratings on switches

Most manufacturers print a voltage rating on the switch at thefactory. Due to limited space, they normally print the highestvoltage at which the switch should be used for on a continuous basisunder normal conditions. Now this is a very controversial statementbecause not everyone's normal is the same. Lets just say dust anddebris not visible, Moisture not high and no extreme temperaturesthat would affect the insulation or mechanical properties of thecomponents.

It needs to be said here that the switch is good for anyvoltage below that rating all the way to zero volts. Under the sameconditions no matter whose definition of normal you use. So if theconnecting device says 600V on it it is also good for 12 VDC or 24VDC or 125 VAC and 250 VAC and so on at any value between 0 and 600AC or DC.

To clear up Amperage ratings on switches

That does not mean that the amperage rating on the switchapplies to all voltages and types of current. As a matter of fact itonly is supposed to apply to the voltage and type stated on theswitch.

If you apply ohms law to voltage and amperage it wouldindicate that if the voltage were half the amperage could double. ICurrent (amperage) = Voltage divided by Resistance. Changing thevoltage of the circuit does not change the resistance. However thatis not true with alternating current. So you can not use ohms law todetermine the amperage value for AC. And there are many moremechanical factors for both DC and AC that have profound affects onarching outside the scope of this discussion. Like materials,speed,pressure, sliding, bouncing, and so on. So it is very important toreach out to the manufacturer of any switch for amperage ratings forthe voltage type and levels you need in the circuit.

Maintained and Momentary explained

A Maintained switch is noted several ways in differentindustries On Off On or Latched or Latching or Locking It is going toLatch Lock in position you or someone else places it. Used for nonjogging operations like pumps fans or lights A momentary switchdenoted in several ways also is (On) Off (On) or Resetting orautomatic reset or springing This term means it will return springreset to a position (usually off) when you release it. For joggingoperations like lift hoist winch or door

What does Pole and Throw refer to

Consider pole to indicate the number of Isolated (individual)Inputs. Throw would be the number of outputs for each pole. Do notconfuse the throws with positions. Any single throw switch can onlyhave 2 positions On Off if you think about it. But a doublethrow switch can have 2 or 3 positions. If a double throw switch has3 positions it is sometimes referred to as On Off On, and willprobably have off as one of the positions. ( usually in the center ).If a double throw switch has only 2 positions then it will alwayshave the input connected to one of the outputs and will not have anoff position for all outputs at same time. This is sometimes referredto as On On.